Extent Error
Extent Error
The other sketches in the part extruded without problem.
Can anyone shed any light as to what I am doing wrong?
Tungsten
Re: Extent Error
Hard to say from the pic, but is it trying to add material or remove material? What's the Extent Depth... is it Zero?
Re: Extent Error
The message says to flip the direction. Is your target on the other side of the part?
-
I may not have gone where I intended to go, but I think I have ended up where I needed to be. -Douglas Adams
I may not have gone where I intended to go, but I think I have ended up where I needed to be. -Douglas Adams
Re: Extent Error
Thanks for replying.
I am wanting to extrude symmetrically but the symmetric button is greyed out in the list of options. As soon as I select the sketch to extrude in either direction I get the error. I am not given the chance to input an extrude depth.
I am wanting to extrude symmetrically but the symmetric button is greyed out in the list of options. As soon as I select the sketch to extrude in either direction I get the error. I am not given the chance to input an extrude depth.
Re: Extent Error
I've attached the file if this helps
- Attachments
-
- Part14.par
- (510.5 KiB) Downloaded 116 times
Re: Extent Error
The steps are.
1) select extrude.
2)Select on Add/Cut. I picked Add.
3) On the Sketch step in the dropdown box pick Select from Sketch .
select the sketch regions click on the green tick
4) on Extent step I picked mid plane 5) Finish.
Hope this helps.
1) select extrude.
2)Select on Add/Cut. I picked Add.
3) On the Sketch step in the dropdown box pick Select from Sketch .
select the sketch regions click on the green tick
4) on Extent step I picked mid plane 5) Finish.
Hope this helps.
Re: Extent Error
Hi,
These are the same steps that I have been using but I still get the error. I've tried remaking the sketch but still cannot get it to extrude.
Tungssten
These are the same steps that I have been using but I still get the error. I've tried remaking the sketch but still cannot get it to extrude.
Tungssten
Re: Extent Error
You need to select the regions of the sketch to extrude as it is not a simple closed boundary. My screen shot shows 2 selected regions. When a region is selected it turns green.
Ideas are simple, once you've thought of them
Re: Extent Error
My selections are also green, but after hitting the green tick button to accept the selection I get the above photo where the selections turn a shade of blue. Also, I cannot the symmetric extent as it is greyed out as seen in photo. Selecting either of the other extents makes no difference.
Re: Extent Error
Maybe this helps show the problem a bit better.
- Attachments
-
- Untitled 69.mp4
- (1.5 MiB) Downloaded 117 times
Re: Extent Error
Hi,
You have to use "Finite extent" instead of through all in Extent step!
BR,
You have to use "Finite extent" instead of through all in Extent step!
BR,
BR,
Imics - SolidEdgeST.wordpress.com
Imics - SolidEdgeST.wordpress.com
Re: Extent Error
He is my screen video.
- Attachments
-
- Boss extrude.wmv
- (1.52 MiB) Downloaded 112 times
Re: Extent Error
Ronan 1961, your video is exactly what I am trying to do but unfortunately, for whatever reason I get the error as soon as I accept the selection with the green tick mark.
Re: Extent Error
Try a sketch with a single closed boundary. Beyond that I don't know. I would upload my part but I am using the Community Edition and the Professional edition won't open it's files.
Ideas are simple, once you've thought of them
Re: Extent Error
This has worked. After setting a distance in "Finite extent" the symmetric button which was previously greyed became active again allowing me to complete the extrude. Many thanks to all who contributed